Adding a New Disk Drive to a Fedora Linux System
Previous | Table of Contents | Next |
Managing and Monitoring Fedora based KVM Guest Systems | Adding a New Disk to a Fedora Volume Group and Logical Volume |
One of the first problems encountered by users these days is that they run out of disk space to store data. Fortunately disk space is now one of the cheapest IT commodities. In the next two chapters we will look at the steps necessary to configure Fedora Linux to use the space provided via the installation of a new internal disk drive.
Mounted Filesystems or Logical Volumes
<google>ADSDAQBOX_FLOW</google> There are two ways to configure a new disk drive into a Fedora Linux system. One very simple method is to create one or more Linux partitions on the new drive, create Linux file systems on those partitions and then mount them at specific mount points so that they can be accessed. This approach will be covered in this chapter of Fedora Linux Essentials.
Another approach is to add the new space to an existing volume group or create a new volume group. When Fedora is installed a volume group is created and called vg_hostname, where hostname is the host name of the Fedora system. Within this volume group are two logical volumes named lv_root and lv_swap that are used to store the / file system and swap partition respectively. By configuring the new disk as part of a volume group we are able to increase the disk space available to the existing logical volumes. Using this approach we are able, therefore, to increase the size of the / file system by allocating some or all of the space on the new disk to lv_root. This topic will be discussed in detail in the chapter entitled Adding a New Disk to a Fedora Volume Group and Logical Volume.
Getting Started
This tutorial assumes that the new physical hard drive has been installed on the system and is visible to the operating system. The best way to do this is to enter the system BIOS during the boot process and ensuring that the BIOS sees the disk drive. Sometimes the BIOS will provide a menu option to scan for new drives. If the BIOS does not see the disk drive double check the connectors and jumper settings (if any) on the drive.
Finding the New Hard Drive in Fedora
Assuming the drive is visible to the BIOS it should automatically be detected by the operating system. Typically, the disk drives in a system are assigned device names beginning hd or sd followed by a letter to indicate the device number. For example, the first device might be /dev/sda, the second /dev/sdb and so on.
The following is output from a system with only one physical disk drive:
ls /dev/sd* /dev/sda /dev/sda1 /dev/sda2
This shows that the disk drive represented by /dev/sda is itself divided into 2 partitions, represented by /dev/sda1 and /dev/sda2.
Another option is to install and run the Hardware Browser. If this is already installed it may be launched by selecting Hardware from the Application->System Tools menu. If this option is not available it may be installed as follows:
su - yum install hwbrowser
In the Hardware Browser select the Hard Drives option to display the current hard disk drive configuration:
The following output is from the same system after a second hard disk drive has been installed:
ls /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sdb
As shown above, the new hard drive has been assigned to the device file /dev/sdb. At this point the drive has no partitions shown (because we have yet to create any).
At this point we have a choice of creating partitions and file systems on the new drive and mounting them for access or adding the disk as a physical volume as part of a volume group. To perform the former continue with this chapter, otherwise read Adding a New Disk to a Fedora Volume Group and Logical Volume for details on configuring Logical Volumes.
Creating Linux Partitions
The next step is to create one or more Linux partitions on the new disk drive. This is achieved using the fdisk utility which takes as a command-line argument the device to be partitioned:
fdisk /dev/sdb Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel Building a new DOS disklabel with disk identifier 0x408bf4fd. Changes will remain in memory only, until you decide to write them. After that, of course, the previous content won't be recoverable. The number of cylinders for this disk is set to 1044. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite) Command (m for help):
In order to view the current partitions on the disk enter the p command:
Command (m for help): p Disk /dev/sdb: 4294 MB, 4294967296 bytes 255 heads, 63 sectors/track, 522 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x338f9c36 Device Boot Start End Blocks Id System
As we can see from the above fdisk output the disk currently has no partitions because it is a previously unused disk. The next step is to create a new partition on the disk, a task which is performed by entering n (for new partition) and p (for primary partition):
Command (m for help): n Command action e extended p primary partition (1-4) p Partition number (1-4):
In this example we only plan to create one partition which will be partition 1. Next we need to specify where the partition will begin and end. Since this is the first partition we need it to start at cylinder 1 and since we want to use the entire disk we specify the last cylinder as the end. Note that if you wish to create multiple partitions you can specify the size of each partition by cylinders, bytes, kilobytes or megabytes.
Partition number (1-4): 1 First cylinder (1-522, default 1): Using default value 1 Last cylinder or +size or +sizeM or +sizeK (1-522, default 522): Using default value 522
Now that we have specified the partition we need to write it to the disk using the w command:
Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. Syncing disks.
If we now look at the devices again we will see that the new partition is visible as /dev/sdb1:
ls /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sdb /dev/sdb1
The new partition will similarly be visible in the Hardware Browser. The next step is to create a filesystem on our new partition.
Creating a Filesystem on a Fedora Disk Partition
We now have a new disk installed, it is visible to Fedora and we have configured a Linux partition on the disk. The next step is to create a Linux file system on the partition so that the operating system can use it to store files and data. The easiest way to create a file system on a partition is to use the mkfs.ext3 utility which takes as arguments the label and the partition device:
/sbin/mkfs.ext3 -L /photos /dev/sdb1 mke2fs 1.40.4 (31-Dec-2007) Filesystem label=/photos OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) 524288 inodes, 1048233 blocks 52411 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=1073741824 32 block groups 32768 blocks per group, 32768 fragments per group 16384 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Writing inode tables: done Creating journal (16384 blocks): done Writing superblocks and filesystem accounting information: done This filesystem will be automatically checked every 38 mounts or 180 days, whichever comes first. Use tune2fs -c or -i to override.
Mounting a Filesystem
Now that we have created a new filesystem on the Linux partition of our new disk drive we need to mount it so that it is accessible. In order to do this we need to create a mount point. A mount point is simply a directory into which the filesystem will be mounted. For the purposes of this example we will create a /photos directory to match our filesystem label (although it is not necessary that these values match):
mkdir /photos
The filesystem may then be manually mounted using the mount command:
mount /dev/sdb1 /photos
Running the mount command with no arguments shows us all currently mounted filesystems (including our new filesystem):
mount /dev/mapper/vg_kvmfed11-lv_root on / type ext4 (rw) proc on /proc type proc (rw) sysfs on /sys type sysfs (rw) devpts on /dev/pts type devpts (rw,gid=5,mode=620) /dev/sda1 on /boot type ext3 (rw) tmpfs on /dev/shm type tmpfs (rw) none on /proc/sys/fs/binfmt_misc type binfmt_misc (rw) sunrpc on /var/lib/nfs/rpc_pipefs type rpc_pipefs (rw) nfsd on /proc/fs/nfsd type nfsd (rw) /dev/sdb1 on /photos type ext3 (rw)
Configuring Fedora to Automatically Mount a Filesystem
In order to set up the system so that the new filesystem is automatically mounted at boot time we an entry needs to be added to the /etc/fstab file.
The following example shows an fstab file configured to automount our /photos partition:
UUID=9a776b27-fd00-4d69-bf8e-9c5629631599 /boot ext3 defaults 1 2 /dev/mapper/vg_fedora11-lv_root / ext4 defaults 1 1 /dev/mapper/vg_fedora11-lv_swap swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults 0 0 devpts /dev/pts devpts defaults 0 0 sysfs /sys sysfs defaults 0 0 proc /proc proc defaults 0 0 LABEL=/photos /photos ext3 defaults 1 2
Previous | Table of Contents | Next |
Managing and Monitoring Fedora based KVM Guest Systems | Adding a New Disk to a Fedora Volume Group and Logical Volume |